Results 1 to 10 of 10

Thread: Back after a looong absence

  1. #1

    Back after a looong absence

    [IMG][/IMG]Been away for way too long. Glad to be back. For your viewing pleasure, my Tiger SVD clone. 317tiger1.jpg

    http://www.gunsnet.net/photopost/sho...=tiger&cat=500
    Last edited by mack8384; 01-26-2013 at 12:41 PM.

  2. #2
    Contributor 02/2014 FunkyPertwee's Avatar

    Join Date
    Jul 2010
    Location
    Whitopia
    Posts
    11,024
    Awesome gun!

    I've always wanted a real SVD.
    "I'm fucking furious, I'm violently angry, and I like it. If you don't know what that feels like then I feel bad for you"

  3. #3
    Senior Member

    Join Date
    Nov 2011
    Posts
    829
    Nice Tigr. Welcome to the club

  4. #4
    Forum Administrator Schuetzenman's Avatar

    Join Date
    Jul 2010
    Location
    East of Atlanta GA
    Posts
    14,616
    Congrats, that's a really high dollar weapon you have there. I think less than 1,000 of those came into the US in that configuration.
    Last edited by Schuetzenman; 01-26-2013 at 05:41 PM.

  5. #5
    Thanx Schuetzman, But in actuality it started out as a regular B-West imported Tiger. I added the russian furniture and the proper hooded front sight and flash hider from Dragunov parts.com (unfortunatly they are no longer in business) and accesories from Tantal. I also installed a modified adjustable gas piston. Too bad for the shorter barrel though or else it would be an almost perfect clone.

  6. #6
    Senior Member

    Join Date
    Jul 2010
    Location
    Southwest, Missouri
    Posts
    150
    AWESOME!!!

    And welcome back.

  7. #7
    Senior Member

    Join Date
    Nov 2011
    Posts
    829
    Hey Mack did you put the flash hider on yourself? If you did does the pin only come out & go in in one direction? I have one I haven't installed yet & didnt know if it is a DIY item?

  8. #8
    nitewathcher, the FSB is actually the stock Tiger one. I installed a custom hood and silver soldered a custom flash hider from Dragunovparts.com years ago since FSB for SVD were amost non existent back then. Now with better availability of true SVD FSB it would be easier to install the complete unit.

    However the standard SVD FSB sits further down the barrel than the stock Tiger FSB. So once you get the SVD FSB seated to proper distance on the barrel you'll have to redrill the retainer pin holes in the barrel.
    The pins holding the FSB on the Tiger or SVD are usually very difficult to get moving. I've found that applying heat from a heat gun and then lots of penetrating oil help loosen the pin. Once the pin is drifted out (the pin looks to be straight rather then tapered but tends to move one way than the other more easily, probably in the opposite direction that it was pressed in from) be prepared for a battle to get the FSB off the barrel. It is an extremly tight press fit. If you don't have a proper press set up for the FSB then I'd suggest heat and pentetrating oil with a big rawhide/plastic mallet. Whenever I apply flame heat to a barrel I use Heat stop paste 9available from Brownells) to keep the heat localized.

    Before trying to remove your FSB mic out the barrel area and the internal diameter of the SVD FSB to make sure they are comparable. If you are lucky the SVD FSB will mic out slightly smaller than the FSB barrel area. You can ream out the SVD FSB to provide a .001-.002 interferance fit (FSB slightly smaller than barrel surface) It should press on very tight if the FSB is heated in an oven and with some lube and provide a nice secure fit. Then you will have to drill a new retainer pin hole/groove using the FSB holes as a guide. If you find that your SVD FSB is larger than your barrel you most likely will end having to silver solder it in place (silver soldier paste and Heat stop paste from Brownells) to prevent it from moving around.
    BTW- The painted surface of the Tiger Barrel doesn't stand up to flame heat very well .
    Hope this answers some of your questions

  9. #9
    Senior Member

    Join Date
    Nov 2011
    Posts
    829
    Thanks Mack I appreciate you taking all that time to explain it to me. That is way more than im comfortable trying to do. I think i'll take to the gunsmith I know.

  10. #10
    Junior Member saltydog's Avatar

    Join Date
    Sep 2013
    Posts
    1
    Its been way too long for me too! I just found this place again!
    I see some old names from long ago! Best Regards......Rick from DragunovPartsUSA

    http://i121.photobucket.com/albums/o...Ricks_Drag.jpg

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •