Results 1 to 6 of 6

Thread: Making Your Own Custom Piston.

  1. #1
    Conributor 09/13 slamfire51's Avatar

    Join Date
    Jul 2010
    Location
    The South
    Posts
    8,200

    Making Your Own Custom Piston.

    Making Your Own Custom Piston.

    Like a lot of builders, I am not blessed with a fully equipped machine shop.
    These modifications are done with basic tools.

    AK pistons have a hard chrome plating to help protect against the effects of corrosive ammo.
    After many attempts to drill, I found heating the piston and shaft with a MAPP torch to a cherry red, and then air cool, will allow drill bits to work better. This heating will not affect the hard chrome plating.


    Most pistons have a divet on the top. Center punch piston dead center. Use a drill press and a machinist vice, and make absolutely sure the piston is parallel with bit.
    Drill with 1/8" drill bit as deep as the piston is long, and add an additional 3/16". Go slow and use oil.



    Piston drilled. (1/8' bit) Leave piston in vice.



    Now use a 5/16" bit and drill slowly and use plenty of oil. Piston drilled with 5/16" bit.



    Piston drilled and cut off shaft.



    Notice piston was drilled dead center. A MUST!!!!



    Cut shaft to needed overall length. This will be the total OAL of the piston Top of the shaft will be flush with the top of piston.



    Bevel the top end of the shaft so the piston will start slightly. Make sure the piston is square to the shaft. Lube the shaft with oil or grease. Set the two pieces in a press, and slowly begin to push, checking at all times that it is not binding.



    After pressing, I drill through the piston and shaft with a 1/8" bit. I then pin the piston to the shaft with a 1/8" tension pin (roll pin). Piston is now done.

    Last edited by slamfire51; 03-25-2011 at 02:34 PM.
    There's no problem an AK can't solve...........


    GUNSNET Member Since 2003
    CCW Permit
    03 FFL

  2. #2
    Moderator & Team GunsNet SILVER 11/2010 Tx Dogblaster's Avatar

    Join Date
    Jul 2010
    Location
    Just out of range
    Posts
    846
    It's nice to see this back where it belongs. Thanks Slam!

  3. #3
    Conributor 09/13 slamfire51's Avatar

    Join Date
    Jul 2010
    Location
    The South
    Posts
    8,200
    Quote Originally Posted by Tx Dogblaster View Post
    It's nice to see this back where it belongs. Thanks Slam!
    I just wish there were more building like the "old" days.
    Still, there are some who haven't built the kits they are sitting on.

    Time to build Guys!!!
    There's no problem an AK can't solve...........


    GUNSNET Member Since 2003
    CCW Permit
    03 FFL

  4. #4
    romak10/63UF
    Guest
    Nice write up ! A+ Job with the pictures. Do you think you could of used a tap an die set to strengthen the piston head ?

  5. #5
    Conributor 09/13 slamfire51's Avatar

    Join Date
    Jul 2010
    Location
    The South
    Posts
    8,200
    Quote Originally Posted by romak10/63UF View Post
    Nice write up ! A+ Job with the pictures. Do you think you could of used a tap an die set to strengthen the piston head ?
    That method is certainly doable. I choose this way because of tools on hand at the time.
    There's no problem an AK can't solve...........


    GUNSNET Member Since 2003
    CCW Permit
    03 FFL

  6. #6
    Moderator & Team GunsNet SILVER 11/2010 Tx Dogblaster's Avatar

    Join Date
    Jul 2010
    Location
    Just out of range
    Posts
    846
    Romak: There's no real strength needed for the piston. The roll pin is more than sufficient. Threading the shank & tapping the piston head would work but it would still need to be pinned or tack welded so it doesn't move. The press & pin method is simple and eliminates threading any of the parts.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •